This feature makes all variations of a selected character accessible. This serves several purposes: An application may not support the feature by which the desired glyph would normally be accessed; the user may need a glyph outside the context supported by the normal substitution, or the user may not know what feature produces the desired glyph. Since many-to-one substitutions are not covered, ligatures would not appear in this table unless they were variant forms of another ligature.

This feature turns capital characters into petite capitals. It is generally used for words which would otherwise be set in all caps, such as acronyms, but which are desired in petite-cap form to avoid disrupting the flow of text. See the pcap feature description for notes on the relationship of caps, smallcaps and petite caps.

This feature turns capital characters into small capitals. It is generally used for words which would otherwise be set in all caps, such as acronyms, but which are desired in small-cap form to avoid disrupting the flow of text.

When available, replaces default glyphs with alternate forms which provide better joining behavior.

Shifts various punctuation marks up to a position that works better with all-capital sequences or sets of lining figures; also changes oldstyle figures to lining figures.

Replaces a sequence of glyphs with a single glyph. This feature covers those ligatures which may be used for special effect, at the user's preference.

Replaces selected figures which follow a slash with denominator figures.

Replaces figures separated by a slash with 'common' (diagonal) fractions.

This feature replaces the default (current) forms with the historical alternates, e.g. the long form of s or the old Fraktur k.

Replaces a sequence of glyphs with a single glyph, e.g. 'fi', 'fl'. This feature is enabled by default and cannot currently be disabled.

This feature changes selected figures from oldstyle to the default lining form.

Replaces selected figures which precede a slash with numerator figures, and replaces the typographic slash with the fraction slash.

Replaces default alphabetic glyphs with the corresponding ordinal forms for use after figures.

Gives the user access to ornament glyphs (e.g. fleurons, dingbats and border elements), either by replacing the bullet character with a selection from the full set of available ornaments, or replacing specific "lower ASCII" characters with ornaments assigned to them.

Some fonts contain an additional size of capital letters, shorter than the regular smallcaps and whimsically referred to as petite caps. Such forms are most likely to be found in designs with a small lowercase x-height, where they better harmonise with lowercase text than the taller smallcaps (for examples of petite caps, see the Emigre type families Mrs Eaves and Filosofia). This feature turns lowercase characters into petite capitals. Forms related to petite capitals, such as specially designed figures, may be included.

Replaces figure glyphs set on uniform (tabular) widths with corresponding glyphs set on glyph-specific (proportional) widths. Tabular widths will generally be the default, but this cannot be safely assumed. Of course this feature would not be present in monospaced designs.

Replaces the default forms with stylistic alternates. Note that there may be more than one stylistic alternate for a given character.

Replaces lining or oldstyle figures with inferior figures (smaller glyphs which sit lower than the standard baseline, primarily for chemical or mathematical notation). May also replace lowercase characters with alphabetic inferiors.

This feature turns lowercase characters into small capitals. Forms related to small capitals, such as oldstyle figures, may be included.

Stylistic alternatives grouped as sets.

The "subs" feature may replace a default glyph with a subscript glyph, or it may combine a glyph substitution with positioning adjustments for proper placement.

Replaces lining or oldstyle figures with superior figures (primarily for footnote indication), and replaces lowercase letters with superior letters (primarily for abbreviated French titles).

Replaces figure glyphs set on proportional widths with corresponding glyphs set on uniform (tabular) widths. Tabular widths will generally be the default, but this cannot be safely assumed. Of course this feature would not be present in monospaced designs.

Some fonts contain both a default form of zero, and an alternative form which uses a diagonal slash through the counter. Especially in condensed designs, it can be difficult to distinguish between 0 and O (zero and capital O) in any situation where capitals and lining figures may be arbitrarily mixed. This feature allows the user to change from the default 0 to a slashed form.